Skip to Content

The Ultimate Guide to Jeep TPM System [Everything about TPM]

Do you wonder what the TPM system means on a jeep? Then, this article is for you. You’ll learn what it means and also get an answer about some common queries. 

What Is TPMS?

TPMS stands for Tire Pressure Monitoring System. TPMS on a Jeep is the system that monitors the air pressure in your tires. It’s used to alert you when your tires need service and lets you know how much air is left in each tire. 

A TPMS can detect a problem before it causes any damage to your car’s engine, wheel bearings, or even brakes. The Jeep Wrangler first used this TPM system in the 2008 year model when it was mandated.

What Does Check TPM system Mean On A Jeep?

If the TPM system light illuminates, do not panic, it means that one or more of your Jeep tires needs to be inspected. Because, your Jeep tires might be over or under inflated.

You should stop driving if the TPMS light appears and check the air pressure in your Jeep tires. Make sure that the tires are inflated as a Vehicle recommendation PSI lever. You can check the number in your vehicle door jamb or check the owner’s manual. The TPMS light can alert you in a few different ways.

TPMS light came on while driving: TPMS light came on while driving due to the low pressures on tires. So, you need to visually inspect the air pressure in your Jeep tires when the light pops up.

TPMS lights turn off and on: This might be happening due to outside temperature affecting the tire’s pressure. You might experience that the light will come on in the morning and it’ll go off after some periods at the warming time of the day. In this case, you need to take your car to your local service station.

When you start the car, TPMS light flashes: You’ll notice that the light will flash for 60 to 90 seconds or your car warning system will malfunction. So, you need to contact a professional mechanic.

How Do I Reset The TPM On My Jeep?

Follow the below process to reset your jeep TPMS. Jeep Wrangler JK shows the process.

  1. First, make sure your Jeep’s tires are properly inflated to the manufacturer’s recommendation, including the back spare. You’ll find the recommended PSI in a sticker located in the door jamb. 
  2. After you inflate all tires to proper PSI, drive your car for 15 to 25 miles an hour for 10 to 15 minutes. Then, you’ll find that the light will turn off.

If you find that the light won’t go off, then it means your tire sensor has a fault. You might need to replace the battery.

How do I turn off the TPMS on my Jeep?

To turn off the TPMS on your Jeep, you can easily do this task with Superchips. This allows you to access your vehicle’s TPMS and modify it according to your needs.

You’ll get the serial numbers of your trail chips. Next, you need to go to the, then fill all your contact information with the device serial number. Then verify the email.

Now, activate the Superchips unit and navigate the menu options. Then, select Setting options and go to the Unlock TPMS Control System and input the code you get by mail.

If you want to disable the TPM control system, access the off-road screen located on the left side. Now, disable it by pressing the TPMS button.

Can I drive my car with the TPMS light on?

No, you cannot drive your car with the TPMS light on. The light is a warning sign that there is a malfunction in the system, and you should have it fixed as soon as possible. If you ride your car, then you’ll face tire failure problems.

How much does it cost to replace a TPMS sensor?

It is difficult to give a definite answer because it depends on the Jeep model and how complicated the system is. However, it could cost anywhere from approximately $50-$100 each.

Final Words

I hope this article helped you to know about what does check TPM system means on a jeep. Also, you’ll get some common question answers you might have regarding the TPMS.

Related Posts:

Leave a comment

Your email address will not be published. Required fields are marked *