Where Is Jack’s Location on Jeep Wrangler: & How to Use It?

Whether you have a flat tire or need to change your brake pads, knowing where the jack is on a Jeep Wrangler is essential,

In case you have trouble finding the jack on your Jeep Wrangler, The most common location for a jack for the Jeep Wrangler is in the trunk. But it can be found in the rear wheel arch and under the motor vehicle. Depending which year’s Wrangler you’re using it may vary.

Here, I’ll first introduce you to the various types of jacks, then show you where the jack is located on a Jeep Wrangler, and last, how to utilize the jack on your vehicle.

Types of jacks for Jeep wrangler-

The Single-arm screw jack:

The first type of jack, the most basic and least expensive, is typically found on entry-level devices or those with limited features. This type of jack only has one movable arm that lifts the car from the ground. This type of jack is lightweight and simple to operate, but it cannot raise high loads.

The double-arm screw jack:

It operates on the same premise as the jack shown above, namely, a worm screw that allows the jack to be raised and lowered by screwing and unscrewing. However, the use of a double arm allows for a more stable jack that can carry a greater payload.

The hydraulic jack:

This type of jack isn’t standard on most vehicles, and it’s normally only included with higher-end models or available for purchase at car dealerships. These jacks are bigger, less bulky, and have the benefit of being considerably easier to use and capable of lifting a larger load.

Where Is the Jack of a Jeep Wrangler Located?

I’ll start with the part that most likely attracted you to this article. Where is the jack location on Jeep Wrangler? It may appear simple, but the position of the jack varies depending on the make and model of the car.

It’s worth noting that most Jeep Wranglers come with a jack. If they don’t, you’ll need to purchase a puncture-proof spray or a compressor instead.

Below, I’ll show you where the jack is located on your Jeep Wrangler. These positions may change depending on the year and finish of your car.

The trunk of your Jeep Wrangler is the most common position for a jack. Simply raise the carpet in the trunk to reveal it, along with the spare tire.

In the rear wheel arch. Your jack could be on your trunk, but on the side of the trunk, and all you have to do to get to it is open the hatch in the right half of your trunk.

The jack’s final probable location on your Jeep Wrangler is under the car. If you still have the spare tire, you’ll find it beneath your trunk, most of the time, you’ll need to loosen a nut to get it and the spare tire out.

How to Use It?

I will now tell you how to use the jack on your jeep wrangler. The procedure is the same whether you’re replacing your wheel or the brake pads on your Jeep Wrangler.

This procedure may appear complex, but following a few guidelines will allow you to operate your jack securely.

Jacking:

  • Remember to activate the brakes and a gear to lock your wheels before raising your Jeep Wrangler.
  • Before raising the Wrangler, unscrew the wheel nuts of the wheels you want to work on; otherwise, you risk harming the gearbox.
  • Start by lifting your jack approximately 20 cm and positioning it under your car at the level of the chassis; in most cases, you’ll find a notch to help you position it correctly.
  • Raise your Jeep Wrangler, but don’t go too much; if your tire falls off three inches off the ground, that’ll suffice.

Common Mistakes When Jacking

1. Failing to support the car:

When using a floor jack, one of the most common safety mistakes is neglecting to support the car with jack supports after it is up in the air.

Although jacks are excellent lifting tools, they should never be used to support a car. All it takes is a leaking hydraulic ram seal, a valve that wasn’t fully closed before you started lifting, or a minor jack misalignment for your automobile to come crashing down on top of you.

2. Using jack on a non-level surface:

I understand that not everyone lives in a desert with a level landscape. Some of us live where finding a flat section of road is difficult.

But when lifting a car, the most common mistake is also the most dangerous. Keep in mind that a jack is only intended to be used for lifting.

It does not provide enough stability on its own to allow someone to work underneath your car safely. While your car is in the air, you should always employ jack stands for extra support.

Your car will not come crashing down on you if the jack slides or the hydraulic ram leaks.

However, convenience is no reason to put you at risk. Using a jack on an uneven surface poses a risk of tipping, which might cause your car to crash. Even if your automobile is on jack stands, this threat exists.

3. Over stressing the capacity:

Using a jack with a capacity that is insufficient for the car you’re trying to raise might cause the jack to break due to stress.

While most floor jacks have a rated capacity that is more than the weight of most passenger vehicles, you must double-check the weight of your vehicle against the jack’s rated capacity.

If the vehicle’s weight exceeds the jack’s capability, upgrade to a larger floor jack.

Precautions

Most hand tools don’t require much maintenance. Just wipe them off and place them in your tool chest. A jack is different, and if you don’t pay attention to maintenance, the consequences might be terrible.

Before each usage, thoroughly examine your jack to ensure that there are no leaks or structural faults. Don’t use your jack if you detect one of these things! It’s time to get rid of it! In any scenario, disregarding these warning indications increases the risk of your jack failing and posing a safety risk.

When you lift your automobile from other places, the jack has a larger probability of falling out from underneath it. Another aspect that influences a floor jack’s stability is its size.

The platform, lifting arms, saddle, and wheelbase must all fit within the appropriate support points on your vehicle’s chassis. So always double check that your Wrangler is in park and the parking brake is engages.

Final Words

A jack can let you work on your car in a safe and controlled setting. You may save money on repairs and avoid major damage if you keep these items in mind.

That’s why it is really important to know where the jack is located on your Jeep Wrangler and how to use it.

Related Posts: