With a severely broken wire harness, you can’t hope to operate your jeep smoothly or safely. You might be concerned about the cost of replacing your wiring harness. But how much will a replacement set you back?
An automobile wire harness replacement costs between $1,300 and $1,700. The cost of labour for the replacement is estimated to be between $400 and $500.
Now you don’t have to be concerned about what possible factors go into figuring the replacement cost because I’ll cover everything you need to know in this article.
Key points:
- The cost of a new wire harness ranges from $1,300 to $1,700. The cost of labour is projected to be between $400 and $500 for the replacement.
- Check the connectors for signs of corrosion or other deterioration to see if your jeep’s wiring harness is damaged.
- You should budget for the average price mentioned in this article, but unexpected repairs or a battery replacement may result in additional costs.
Jeep Wrangler Wiring Harness Cost (Updated Price)
Before preparing or deciding to replace the jeep wrangler wiring harness, you must have exact information or an overview of the estimated expenditure.
To assist you right now, I’ll reveal and clarify every detail of this replacement project, including expected costs.
It can take an hour to install a wiring harness if it is easy to access. However, if the car has a difficult-to-work-on engine configuration. It’s possible that you’ll have to work for 10-20 hours.
The wire harness will set you back around $300 maximum and $100 minimum. The bare minimum in terms of labour costs is roughly $400.
This is for 3-4 hours of work; however, most people work for 6-8 hours. If you want 10-20 hours of labour, you should budget between $800 and $1500.
This estimate, however, will definitely fluctuate based on a number of important aspects. Working with a tiny garage can affect the amount of money you’ll need to spend on this service, and warranty work will be paid differently, of course.
Because most people are unable to complete this operation at home, labour costs are difficult to avoid. It’s probably best to go for professional to do it for you.
You should also be sceptical of offers for extremely low-cost services. This could signify that you’ll be getting bad work in exchange for your money.
| Model | Labour Cost | Parts |
| Honda Civic | $600-$800 | $100 |
| Chevrolet Silverado | $1,000-$1,500 | $300 |
| Mercedes-Benz | $2,000 | $500 |
| Acura | $1,000 | $300 |
| Chevrolet Suburban | $1,200 | $200 |
| Chevrolet Camaro | $800 | $400 |
| Ferrari | $2,000 | $1,500 |
The cost of your wiring harness and the labour required to install it varies depending on the make and model of your vehicle.
The price of a wiring harness varies depending on the manufacturer. Components for luxury automobiles are normally more expensive than parts for domestic vehicles, although larger vehicles may have more expensive parts for this type of maintenance as well.
The wiring harness usually costs no more than $500. The expense of labour is where it may really mount up.
When Should You Replace Your Jeep Wrangler Wiring Harness?
Users rely on wire harness for anything from remote control cars to power equipment, as well as high-stakes installations like security systems. Recognizing when a wire harness is damaged will allow you to repair or replace it before it starts to influence the operation of the device in which it is mounted.
To ensure that your jeep’s wire harness is damaged, check the connectors for evidence of corrosion or other deterioration. Look for symptoms of cracking, drying out, or warping in the insulating wire wrapping.
Even if your electronics are performing as expected, there are symptoms that your wire harness assembly is no longer performing as it should.Other faults may be discovered during a visual check, indicating that your equipment needs to be repaired or replaced.
You don’t need a replacement harness unless you’ve had a car fire or another catastrophic accident that has damaged a significant section of the automobile’s wiring. Repair only the faulty wiring. Insulation on the wires is brittle and stiff. The connectors are mostly rusted and damaged.
Broken or Damaged Wiring Harness Replacement Guideline:
It’s necessary to replace the wire harness if it’s faulty. If an electrical connector, for example, melts or burns, you may need to do this repair. If not replaced as quickly as possible, a melted or burned electrical connector can heat up and start a fire.
Step 1: Cut Open the Wiring Loom
Remove the wiring from the loom and inspect it for damage. Check for any signs of burning, melting, or tearing in the wire.
Step 2: Verify that the old and new connectors are identical
Make that the new and old electrical connectors are same. The colour of the wiring will most likely not match the original unless the replacement electrical connector comes from the factory.
Step 3: Replacing the Wiring Harness is to Strip the Ends of the Wires
The next step is to strip the wires to the length of the cutting blade on the wire cutters.
Step 4: Twist the wires’ ends together
The wires must then be securely twisted.
Step 5: Connect the wires with an insulated connector
Crimp each wire on the electrical connector to a weatherproof shielded connector. The wire should be crimped to the electrical connector. To verify the connection, tug on the wires. They should be able to pull out of the connector without loosening it.
Step 6: Melt the Insulated Connector to the Wiring
With a lighter, melt the connector to the wiring. To avoid melting the electrical wire, sway the lighter back and forth.
Step 7: Apply Electrical Tape to the Wire
Wrap the wire with electrical tape once the connector has cooled to add an extra layer of protection. On avoid exerting pressure to the connector, do not lay tape too close to it.
Is Your Jeep Wiring Harness Covered Under Insurance?
Furthermore, auto vehicle wiring harness replacement is covered by a car insurance policy provision, so the entire replacement process can be completed under the policy.
Although the cost of replacement varies greatly based on your location, the state of your car, and the service provider who will be attending you, your insurance company must still reimburse the cost.
Final words
Despite the fact that vehicle wiring harness repair is costly, it could save you from a variety of fire threats and accidents. Nothing is more expensive than a human life. If the harness wire appears worn out, don’t hesitate to replace it.
There are a number of factors that can increase the overall cost of replacing your vehicle wiring. You should budget for the average price stated in this article, but extra repairs or a battery replacement may incur additional charges.
Always keep in mind that exotics and luxury jeeps are more expensive to work on, and the parts for wiring harness repairs are also more expensive overall.
Related Posts:
